Showing posts with label flash. Show all posts
Showing posts with label flash. Show all posts

Sunday, 17 July 2011

Gamma-ray flash came from star being eaten by massive black hole

ScienceDaily (June 16, 2011) — A bright flash of gamma rays observed March 28 by the Swift satellite may have been the death rattle of a star falling into a massive black hole and being ripped apart, according to a team of astronomers led by the University of California, Berkeley.

When the Swift Gamma Burst Mission spacecraft first detected the flash within the constellation Draco, astronomers thought it was a gamma-ray burst from a collapsing star. On March 31, however, UC Berkeley's Joshua Bloom sent out an email circular suggesting that it wasn't a typical gamma-ray burst at all, but a high-energy jet produced as a star about the size of our sun was shredded by a black hole a million times more massive.

Careful analysis of the Swift data and subsequent observations by the Hubble Space Telescope and the Chandra X-ray Observatory confirmed Bloom's initial insight. The details are published online on June 16 in Science Express, a rapid publication arm of the journal Science.

"This is truly different from any explosive event we have seen before," Bloom said.

What made this gamma-ray flare, called Sw 1644+57, stand out from a typical burst were its long duration and the fact that it appeared to come from the center of a galaxy nearly 4 billion light years away. Since most, if not all, galaxies are thought to contain a massive black hole at the center, a long-duration burst could conceivably come from the relatively slow tidal disruption of an infalling star, the astronomers said.

"This burst produced a tremendous amount of energy over a fairly long period of time, and the event is still going on more than two and a half months later," said Bloom, an associate professor of astronomy at UC Berkeley. "That's because as the black hole rips the star apart, the mass swirls around like water going down a drain, and this swirling process releases a lot of energy."

Bloom and his colleagues propose in their Science Express paper that some 10 percent of the infalling star's mass is turned into energy and irradiated as X-rays from the swirling accretion disk or as X-rays and higher energy gamma rays from a relativistic jet that punches out along the rotation axis. Earth just happened to be in the eye of the gamma-ray beam.

Bloom draws an analogy with a quasar, which is a distant galaxy that emits bright, high-energy light because of the massive black hole at its center gobbling up stars and sending out a jet of X-rays along its rotation axis. Observed from an angle, these bright emissions are called active galactic nuclei, but when observed down the axis of the jet, they're referred to as blazars.

"We argue that this must be jetted material and we're looking down the barrel," he said. "Jetting is a common phenomenon when you have accretion disks, and black holes actually prefer to make jets."

Looking back at previous observations of this region of the cosmos, Bloom and his team could find no evidence of X-ray or gamma-ray emissions, leading them to conclude that this is a "one-off event," Bloom said.

"Here, you have a black hole sitting quiescently, not gobbling up matter, and all of a sudden something sets it off," Bloom said. "This could happen in our own galaxy, where a black hole sits at the center living in quiescence, and occasionally burbles or hiccups as it swallows a little bit of gas. From a distance, it would appear dormant, until a star randomly wanders too close and is shredded."

Probable tidal disruptions of a star by a massive black hole have previously been seen at X-ray, ultraviolet and optical wavelengths, but never before at gamma-ray energies. Such random events, especially looking down the barrel of a jet, are incredibly rare, "probably once in 100 million years in any given galaxy," said Bloom. "I would be surprised if we saw another one of these anywhere in the sky in the next decade."

The astronomers suspect that the gamma-ray emissions began March 24 or 25 in the uncatalogued galaxy at a redshift of 0.3534, putting it at a distance of about 3.8 billion light years. Bloom and his colleagues estimate that the emissions will fade over the next year.

"We think this event was detected around the time it was as bright as it will ever be, and if it's really a star being ripped apart by a massive black hole, we predict that it will never happen again in this galaxy," he said.

Bloom's colleagues include UC Berkeley theoretical physicist Elliot Quataert, who models the production of jets from accretion disks, and UC Berkeley astronomers S. Bradley Cenko, Daniel A. Perley, Nathaniel R. Butler, Linda E. Strubbe, Antonino Cucchiara, Geoffrey C. Bower and Adam N. Morgan; Dimitrios Giannios and Brian D. Metzger of Princeton University; Andrew J. Levan of the University of Warwick, Coventry, United Kingdom; Nial R. Tanvir, Paul T. O' Brien, Andrew R. King and Sergei Nayakshin of the University of Leicester in the U.K.; Fabio De Colle, Enrico Ramirez-Ruiz and James Guillochon of UC Santa Cruz; William H. Lee of the Universidad Nacional Autonoma de México in Mexico City; Andrew S. Fruchter of the Space Telescope Science Institute in Baltimore, Md.; and Alexander J. van der Horst of the Universities Space Research Association in Huntsville, Ala.

Levan is first author of the companion Science Express paper, and leader of the Chandra and Hubble Space Telescope observation team.

Bloom and his laboratory are supported by grants from NASA and the National Science Foundation.

Story Source:

The above story is reprinted (with editorial adaptations by ScienceDaily staff) from materials provided by University of California - Berkeley.

Journal Reference:

Joshua S. Bloom, Dimitrios Giannios, Brian D. Metzger, S. Bradley Cenko, Daniel A. Perley, Nathaniel R. Butler, Nial R. Tanvir, Andrew J. Levan, Paul T. O' Brien, Linda E. Strubbe, Fabio De Colle, Enrico Ramirez-Ruiz, William H. Lee, Sergei Nayakshin, Eliot Quataert, Andrew R. King, Antonino Cucchiara, James Guillochon, Geoffrey C. Bower, Andrew S. Fruchter, Adam N. Morgan, Alexander J. Van Der Horst. A Possible Relativistic Jetted Outburst from a Massive Black Hole Fed by a Tidally Disrupted Star. Science, 16 June 2011 DOI: 10.1126/science.1207150

Note: If no author is given, the source is cited instead.

Disclaimer: Views expressed in this article do not necessarily reflect those of ScienceDaily or its staff.


View the original article here

Monday, 27 June 2011

New way to make lighter, stronger steel -- in a flash

ScienceDaily (June 9, 2011) — A Detroit entrepreneur surprised university engineers in Ohio recently, when he invented a heat-treatment that makes steel 7 percent stronger than any steel on record -- in less than 10 seconds.

In fact, the steel, now trademarked as Flash Bainite, has tested stronger and more shock-absorbing than the most common titanium alloys used by industry.

Now the entrepreneur is working with researchers at Ohio State University to better understand the science behind the new treatment, called flash processing.

What they've discovered may hold the key to making cars and military vehicles lighter, stronger, and more fuel-efficient.

In the current issue of the journal Materials Science and Technology, the inventor and his Ohio State partners describe how rapidly heating and cooling steel sheets changes the microstructure inside the alloy to make it stronger and less brittle.

The basic process of heat-treating steel has changed little in the modern age, and engineer Suresh Babu is one of few researchers worldwide who still study how to tune the properties of steel in detail. He's an associate professor of materials science and engineering at Ohio State, and Director of the National Science Foundation (NSF) Center for Integrative Materials Joining for Energy Applications, headquartered at the university.

"Steel is what we would call a 'mature technology.' We'd like to think we know most everything about it," he said. "If someone invented a way to strengthen the strongest steels even a few percent, that would be a big deal. But 7 percent? That's huge."

Yet, when inventor Gary Cola initially approached him, Babu didn't know what to think.

"The process that Gary described -- it shouldn't have worked," he said. "I didn't believe him. So he took my students and me to Detroit."

Cola showed them his proprietary lab setup at SFP Works, LLC., where rollers carried steel sheets through flames as hot as 1100 degrees Celsius and then into a cooling liquid bath.

Though the typical temperature and length of time for hardening varies by industry, most steels are heat-treated at around 900 degrees Celsius for a few hours. Others are heated at similar temperatures for days.

Cola's entire process took less than 10 seconds.

He claimed that the resulting steel was 7 percent stronger than martensitic advanced high-strength steel. [Martensitic steel is so named because the internal microstructure is entirely composed of a crystal form called martensite.] Cola further claimed that his steel could be drawn -- that is, thinned and lengthened -- 30 percent more than martensitic steels without losing its enhanced strength.

If that were true, then Cola's steel could enable carmakers to build frames that are up to 30 percent thinner and lighter without compromising safety. Or, it could reinforce an armored vehicle without weighing it down.

"We asked for a few samples to test, and it turned out that everything he said was true," said Ohio State graduate student Tapasvi Lolla. "Then it was up to us to understand what was happening."

Cola is a self-taught metallurgist, and he wanted help from Babu and his team to reveal the physics behind the process -- to understand it in detail so that he could find ways to adapt it and even improve it.

He partnered with Ohio State to provide research support for Brian Hanhold, who was an undergraduate student at the time, and Lolla, who subsequently earned his master's degree working out the answer.

Using an electron microscope, they discovered that Cola's process did indeed form martensite microstructure inside the steel. But they also saw another form called bainite microstructure, scattered with carbon-rich compounds called carbides.

In traditional, slow heat treatments, steel's initial microstructure always dissolves into a homogeneous phase called austenite at peak temperature, Babu explained. But as the steel cools rapidly from this high temperature, all of the austenite normally transforms into martensite.

"We think that, because this new process is so fast with rapid heating and cooling, the carbides don't get a chance to dissolve completely within austenite at high temperature, so they remain in the steel and make this unique microstructure containing bainite, martensite and carbides," Babu said.

Lolla pointed out that this unique microstructure boosts ductility -- meaning that the steel can crumple a great deal before breaking -- making it a potential impact-absorber for automotive applications.

Babu, Lolla, Ohio State research scientist Boian Alexandrov, and Cola co-authored the paper with Badri Narayanan, a doctoral student in materials science and engineering.

Now Hanhold is working to carry over his lessons into welding engineering, where he hopes to solve the problem of heat-induced weakening during welding. High-strength steel often weakens just outside the weld joint, where the alloy has been heated and cooled. Hanhold suspects that bringing the speed of Cola's method to welding might minimize the damage to adjacent areas and reduce the weakening.

If he succeeds, his discovery will benefit industrial partners of the NSF Center for Integrative Materials Joining Science for Energy Applications, which formed earlier this year. Ohio State's academic partners on the center include Lehigh University, the University of Wisconsin-Madison, and the Colorado School of Mines.

Story Source:

The above story is reprinted (with editorial adaptations by ScienceDaily staff) from materials provided by Ohio State University. The original article was written by Pam Frost Gorder.

Journal Reference:

T. Lolla, G. Cola, B. Narayanan, B. Alexandrov, S. S. Babu. Development of rapid heating and cooling (flash processing) process to produce advanced high strength steel microstructures. Materials Science and Technology, 2011; 27 (5): 863-875(13) DOI: 10.1179/174328409X433813

Note: If no author is given, the source is cited instead.

Disclaimer: Views expressed in this article do not necessarily reflect those of ScienceDaily or its staff.


View the original article here

Saturday, 25 June 2011

New way to make lighter, stronger steel -- in a flash

ScienceDaily (June 9, 2011) — A Detroit entrepreneur surprised university engineers in Ohio recently, when he invented a heat-treatment that makes steel 7 percent stronger than any steel on record -- in less than 10 seconds.

In fact, the steel, now trademarked as Flash Bainite, has tested stronger and more shock-absorbing than the most common titanium alloys used by industry.

Now the entrepreneur is working with researchers at Ohio State University to better understand the science behind the new treatment, called flash processing.

What they've discovered may hold the key to making cars and military vehicles lighter, stronger, and more fuel-efficient.

In the current issue of the journal Materials Science and Technology, the inventor and his Ohio State partners describe how rapidly heating and cooling steel sheets changes the microstructure inside the alloy to make it stronger and less brittle.

The basic process of heat-treating steel has changed little in the modern age, and engineer Suresh Babu is one of few researchers worldwide who still study how to tune the properties of steel in detail. He's an associate professor of materials science and engineering at Ohio State, and Director of the National Science Foundation (NSF) Center for Integrative Materials Joining for Energy Applications, headquartered at the university.

"Steel is what we would call a 'mature technology.' We'd like to think we know most everything about it," he said. "If someone invented a way to strengthen the strongest steels even a few percent, that would be a big deal. But 7 percent? That's huge."

Yet, when inventor Gary Cola initially approached him, Babu didn't know what to think.

"The process that Gary described -- it shouldn't have worked," he said. "I didn't believe him. So he took my students and me to Detroit."

Cola showed them his proprietary lab setup at SFP Works, LLC., where rollers carried steel sheets through flames as hot as 1100 degrees Celsius and then into a cooling liquid bath.

Though the typical temperature and length of time for hardening varies by industry, most steels are heat-treated at around 900 degrees Celsius for a few hours. Others are heated at similar temperatures for days.

Cola's entire process took less than 10 seconds.

He claimed that the resulting steel was 7 percent stronger than martensitic advanced high-strength steel. [Martensitic steel is so named because the internal microstructure is entirely composed of a crystal form called martensite.] Cola further claimed that his steel could be drawn -- that is, thinned and lengthened -- 30 percent more than martensitic steels without losing its enhanced strength.

If that were true, then Cola's steel could enable carmakers to build frames that are up to 30 percent thinner and lighter without compromising safety. Or, it could reinforce an armored vehicle without weighing it down.

"We asked for a few samples to test, and it turned out that everything he said was true," said Ohio State graduate student Tapasvi Lolla. "Then it was up to us to understand what was happening."

Cola is a self-taught metallurgist, and he wanted help from Babu and his team to reveal the physics behind the process -- to understand it in detail so that he could find ways to adapt it and even improve it.

He partnered with Ohio State to provide research support for Brian Hanhold, who was an undergraduate student at the time, and Lolla, who subsequently earned his master's degree working out the answer.

Using an electron microscope, they discovered that Cola's process did indeed form martensite microstructure inside the steel. But they also saw another form called bainite microstructure, scattered with carbon-rich compounds called carbides.

In traditional, slow heat treatments, steel's initial microstructure always dissolves into a homogeneous phase called austenite at peak temperature, Babu explained. But as the steel cools rapidly from this high temperature, all of the austenite normally transforms into martensite.

"We think that, because this new process is so fast with rapid heating and cooling, the carbides don't get a chance to dissolve completely within austenite at high temperature, so they remain in the steel and make this unique microstructure containing bainite, martensite and carbides," Babu said.

Lolla pointed out that this unique microstructure boosts ductility -- meaning that the steel can crumple a great deal before breaking -- making it a potential impact-absorber for automotive applications.

Babu, Lolla, Ohio State research scientist Boian Alexandrov, and Cola co-authored the paper with Badri Narayanan, a doctoral student in materials science and engineering.

Now Hanhold is working to carry over his lessons into welding engineering, where he hopes to solve the problem of heat-induced weakening during welding. High-strength steel often weakens just outside the weld joint, where the alloy has been heated and cooled. Hanhold suspects that bringing the speed of Cola's method to welding might minimize the damage to adjacent areas and reduce the weakening.

If he succeeds, his discovery will benefit industrial partners of the NSF Center for Integrative Materials Joining Science for Energy Applications, which formed earlier this year. Ohio State's academic partners on the center include Lehigh University, the University of Wisconsin-Madison, and the Colorado School of Mines.

Story Source:

The above story is reprinted (with editorial adaptations by ScienceDaily staff) from materials provided by Ohio State University. The original article was written by Pam Frost Gorder.

Journal Reference:

T. Lolla, G. Cola, B. Narayanan, B. Alexandrov, S. S. Babu. Development of rapid heating and cooling (flash processing) process to produce advanced high strength steel microstructures. Materials Science and Technology, 2011; 27 (5): 863-875(13) DOI: 10.1179/174328409X433813

Note: If no author is given, the source is cited instead.

Disclaimer: Views expressed in this article do not necessarily reflect those of ScienceDaily or its staff.


View the original article here